Deciduous trees like maples (those that loose their leaves in the fall) can be dug up and sold with their bare roots exposed. Because most of the root system is lost in digging, sufficient top growth should be removed to compensate for this loss. This may be done at the nursery before you buy the plant or you may have to prune at the time of planting. Select and head back the best scaffold branches, i.e. those branches which will form the main lateral structure of the future mature tree. Remove all other extraneous side branches. If the tree seedling does not have branches, allow it to grow to the desired height of branching then pinch it back to stimulate the lower buds to form branches.

Ball and burlap trees are dug up with their root systems somewhat intact. This was mostly done for conifers and broadleaf evergreens, but has become common for deciduous trees as well. Since some root mass is lost in the digging stage, a light pruning is generally called for. Head back the plant to compensate for this loss and to promote branching.

Trees that are grown in containers generally do not loose roots in the transplanting phase. Therefore you do not generally have to prune them unless there is some root injury or limb damage in the planting process.

Once you have your trees planted, be patient. Do not remove shoots from the trunk early on as these allow the tree to grow more rapidly and also shade the tender young trunk from sun-scald. Wait a few years to begin training the tree to its ultimate form.

How-to : Planting Shrubs

Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.

Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.

If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.

If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.

How-to : Staking Trees

Staking is done differently depending on the size and flexibility of the tree, and the windiness of the planting site. Generally only trees that are planted in windy, exposed locations need to be staked. For most trees, a low stake is preferred, to let the tree move naturally. For windy areas or flexible trees, use a high stake. For trees more than 12 feet tall, use two low stakes on opposite sides of the tree or several guy ropes. The ties used need to accommodate growth and not cause bark damage with friction. Buckle-and-spacer ties can be found at garden centers, they are expandable and have a protective spacer. Ties without spacers should be formed into a figure eight to create padding. Latest studies have shown that when staking a tree, provide enough leeway so that the tree can move back and forth in the wind. Stronger roots will develop this way. If the tree can not move back and forth, these important roots will not develop and the tree might fall over during a storm, once stakes are removed. When planting a tree, stake at the time of planting if staking is a necessity.

How-to : Planting a Tree

Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.

If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.

If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.

Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.

Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.