Cryptomeria japonica ( Elegans Japanese Cedar )

Characteristics

Cultivar:	Elegans
Family:	Taxodiaceae
Size:	Height: 20 ft. to 30 ft. Width: 0 ft. to 0 ft.
Plant Category:	trees,
Plant Characteristics:
Foliage Characteristics:	evergreen,
Foliage Color:	blue-green to gold, green,
Flower Characteristics:
Flower Color:
Tolerances:	deer, slope,

Requirements

Bloomtime Range:	not applicable
USDA Hardiness Zone:	6 to 9
AHS Heat Zone:	Not defined for this plant
Light Range:	Part Shade to Full Sun
pH Range:	5.5 to 7.5
Soil Range:	Mostly Sand to Some Clay
Water Range:	Normal to Moist

Plant Care

Fertilizing

How-to : Fertilization for Established Plants

Established plants can benefit from fertilization. Take a visual inventory of your landscape. Trees need to be fertilized every few years. Shrubs and other plants in the landscape can be fertilized yearly. A soil test can determine existing nutrient levels in the soil. If one or more nutrients is low, a specific instead of an all-purpose fertilizer may be required. Fertilizers that are high in N, nitrogen, will promote green leafy growth. Excess nitrogen in the soil can cause excessive vegetative growth on plants at the expense of flower bud development. It is best to avoid fertilizing late in the growing season. Applications made at that time can force lush, vegetative growth that will not have a chance to harden off before the onset of cold weather.

Light

Conditions : Full to Partial Sun

Full sunlight is needed for many plants to assume their full potential. Many of these plants will do fine with a little less sunlight, although they may not flower as heavily or their foliage as vibrant. Areas on the southern and western sides of buildings usually are the sunniest. The only exception is when houses or buildings are so close together, shadows are cast from neighboring properties. Full sun usually means 6 or more hours of direct unobstructed sunlight on a sunny day. Partial sun receives less than 6 hours of sun, but more than 3 hours. Plants able to take full sun in some climates may only be able to tolerate part sun in other climates. Know the culture of the plant before you buy and plant it!

Watering

Problems : Creating a Water Ring

A water ring, sometimes called a water well, is a mound of compacted soil that is built around the circumference of a planting hole once a plant has been installed. The water ring helps to direct water to the outer edges of a planting hole, encouraging new roots to grow outward, in search of moisture. The height of the mound of soil will vary from a couple of inches for 3 gallon shrubs, to almost a foot for balled and burlapped trees, especially those planted on a slope. Mulch over the ring will help to further conserve moisture and prevent deterioration of the ring itself. Once a plant is established, the water ring may be leveled, but you should continue to mulch beneath the plant.

Conditions : Normal Watering for Outdoor Plants

Normal watering means that soil should be kept evenly moist and watered regularly, as conditions require. Most plants like 1 inch of water a week during the growing season, but take care not to over water. The first two years after a plant is installed, regular watering is important for establishment. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.

Planting

How-to : Staking Trees

Staking is done differently depending on the size and flexibility of the tree, and the windiness of the planting site. Generally only trees that are planted in windy, exposed locations need to be staked. For most trees, a low stake is preferred, to let the tree move naturally. For windy areas or flexible trees, use a high stake. For trees more than 12 feet tall, use two low stakes on opposite sides of the tree or several guy ropes. The ties used need to accommodate growth and not cause bark damage with friction. Buckle-and-spacer ties can be found at garden centers, they are expandable and have a protective spacer. Ties without spacers should be formed into a figure eight to create padding. Latest studies have shown that when staking a tree, provide enough leeway so that the tree can move back and forth in the wind. Stronger roots will develop this way. If the tree can not move back and forth, these important roots will not develop and the tree might fall over during a storm, once stakes are removed. When planting a tree, stake at the time of planting if staking is a necessity.

How-to : Planting a Tree

Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.

If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.

If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.

Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.

Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.

Problems

Diseases : Pythium and Phytophtora Root Rot

Rot Rot, Pythium or Phytophthora occurs when soil moisture levels are excessively high and fungal spores present in the soil, come in contact with the susceptible plant. The base of stems discolor and shrink, and leaves further up the stalk wilt and die. Leaves near base are affected first. The roots will turn black and rot or break. This fungi can be introduced by using unsterilized soil mix or contaminated water.

Prevention and Control Remove affected plants and their roots, and discard surrounding soil. Replace with plants that are not susceptible, and only use fresh, sterilized soil mix. Hold back on fertilizing too. Try not to over water plants and make sure that soil is well drained prior to planting. This fungus is not treatable by chemicals.

Rhizoctonia Root and Stem Rot symptoms look similar to Pythium Root Rot, but the Rhizoctonia fungus seems to thrive in well drained soils.

Miscellaneous

Glossary : Evergreen

Evergreen refers to plants that hold onto their leaves or needles for more than one growing season, shedding them over time. Some plants such as live oaks are evergreen, but commonly shed the majority of their older leaves around the end of January.

Plant Images