Haplopappus acaulis ( Haplopappus )

Characteristics

Cultivar:	n/a
Family:	Asteraceae
Size:	Height: 0.5 ft. to 0.5 ft. Width: 1.5 ft. to 1.5 ft.
Plant Category:	ground covers, shrubs,
Plant Characteristics:	low maintenance,
Foliage Characteristics:	evergreen,
Foliage Color:	dark green,
Flower Characteristics:	single,
Flower Color:	yellows,
Tolerances:	deer,

Requirements

Bloomtime Range:	Early Summer to Late Summer
USDA Hardiness Zone:	3 to 7
AHS Heat Zone:	Not defined for this plant
Light Range:	Full Sun to Full Sun
pH Range:	5.5 to 8
Soil Range:	Sandy Loam to Clay Loam
Water Range:	Normal to Normal

Plant Care

Fertilizing

How-to : Fertilization for Young Plants

Young plants need extra phosphorus to encourage good root development. Look for a fertilizer that has phosphorus, P, in it(the second number on the bag.) Apply recommended amount for plant per label directions in the soil at time of planting or at least during the first growing season.

Light

Conditions : Types of Pruning

Types of pruning include: pinching, thinning, shearing and rejuvenating.

Pinching is removing the stem tips of a young plant to promote branching. Doing this avoids the need for more severe pruning later on.

Thinning involves removing whole branches back to the trunk. This may be done to open up the interior of a plant to let more light in and to increase air circulation that can cut down on plant disease. The best way to begin thinning is to begin by removing dead or diseased wood.

Shearing is leveling the surface of a shrub using hand or electric shears. This is done to maintain the desired shape of a hedge or topiary.

Rejuvenating is removal of old branches or the overall reduction of the size of a shrub to restore its original form and size. It is recommended that you do not remove more than one third of a plant at a time. Remember to remove branches from the inside of the plant as well as the outside. When rejuvenating plants with canes, such as nandina, cut back canes at various heights so that plant will have a more natural look.

Conditions : Full Sun

Full Sun is defined as exposure to more than 6 hours of continuous, direct sun per day.

Watering

Problems : Waterlogged Soil and Solutions

Waterlogged soil occurs when more water is added to soil than can drain out in a reasonable amount of time. This can be a severe problem where water tables are high or soils are compacted. Lack of air space in waterlogged soil makes it almost impossible for soil to drain. Few plants, except for bog plants, can tolerate these conditions. Drainage must be improved if you are not satisfied with bog gardening. Over-watered plants have the same wilted leaves as under-watered plants. Fungi such as Phytophthora and Pythium affect vascular systems, which cause wilt.

If the problem is only on the surface, it maybe diverted to a drainage ditch. If drainage is poor where water table is high, install an underground drainage system. You should contact a contractor for this. If underground drains already exist, check to see if they are blocked.

French drains are another option. French drains are ditches that have been filled with gravel. It is okay to plant sod on top of them. More obtrusive, but a good solution where looks aren't as important, think of the French drain as a ditch filled with gravel. Ditches should be 3 to 4 feet deep and have sloping sides.

A soakway is a gravel filled pit where water is diverted to via underground pipes. This works well on sites that have compacted soil. Your soakway should be about 6'wide and deep and filled with gravel or crushed stone, topped with sand and sodded or seeded.

Keep in mind that it is illegal to divert water onto other people's property. If you do not feel that you can implement a workable solution on your own, call a contractor.

Tools : Watering Aides

No gardener depends 100% on natural rainfall. Even the most water conscious garden appreciates the proper hose, watering can or wand.

Watering Cans: Whether you choose plastic of galvanized makes no difference, but do look for generous capacity and a design that is balanced when filled with water. A 2 gallon can (which holds 18 lbs. of water) is preferred by most gardeners and is best suited for outdoor use. Indoor cans should be relatively smaller with narrower spouts and roses (the filter head).

Watering Hose: When purchasing a hose, look for one that is double-walled, as it will resist kinking. Quick coupler links are nice to have on ends of hoses to make altering length fast. To extend the life of your hose, keep it wound around a reel and stored in a shady area. Prior to winter freezes, drain hose.

Sprayers: Are commonly thought of as devices for applying chemicals, but can really be a step saver for watering houseplants or small pots of annuals rather that dragging out a hose or making numerous trips with a watering can. The backpack sprayer is best suited for this. Take care not to use any kind of chemical in tanks used for watering!

Sprinklers: Attached to the ends of garden hoses, these act as an economical irrigation system. Standing Spike Sprinklers are usually intended for lawns and deliver water in a circular pattern. Rotating Sprinklers deliver a circle of water and are perfect for lawns, shrubs and flower beds. Pulse-jet sprinklers cover large areas of ground in a pulsating, circular pattern. The head usually sits up on a tall stem, except for when watering lawns. Oscillating sprinklers are best for watering at ground level in a rectangular pattern.

Conditions : Dry

Dry is defined as an area that regularly receives water, but is fast draining. This results in a soil that is often dry to a depth of 18 inches.

Conditions : Outdoor Watering

Plants are almost completely made up of water so it is important to supply them with adequate water to maintain good plant health. Not enough water and roots will wither and the plant will wilt and die. Too much water applied too frequently deprives roots of oxygen leading to plant diseases such as root and stem rots. The type of plant, plant age, light level, soil type and container size all will impact when a plant needs to be watered. Follow these tips to ensure successful watering:

* The key to watering is water deeply and less frequently. When watering, water well, i.e. provide enough water to thoroughly saturate the root ball. With in-ground plants, this means thoroughly soaking the soil until water has penetrated to a depth of 6 to 7 inches (1' being better). With container grown plants, apply enough water to allow water to flow through the drainage holes.

* Try to water plants early in the day or later in the afternoon to conserve water and cut down on plant stress. Do water early enough so that water has had a chance to dry from plant leaves prior to night fall. This is paramount if you have had fungus problems.

* Don't wait to water until plants wilt. Although some plants will recover from this, all plants will die if they wilt too much (when they reach the permanent wilting point).

* Consider water conservation methods such as drip irrigation, mulching, and xeriscaping. Drip systems which slowly drip moisture directly on the root system can be purchased at your local home and garden center. Mulches can significantly cool the root zone and conserve moisture.

* Consider adding water-saving gels to the root zone which will hold a reserve of water for the plant. These can make a world of difference especially under stressful conditions. Be certain to follow label directions for their use.

Conditions : Normal Watering for Outdoor Plants

Normal watering means that soil should be kept evenly moist and watered regularly, as conditions require. Most plants like 1 inch of water a week during the growing season, but take care not to over water. The first two years after a plant is installed, regular watering is important for establishment. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.

Planting

How-to : Pruning Flowering Shrubs

It is necessary to prune your deciduous flowering shrub for two reasons: 1. By removing old, damaged or dead wood, you increase air flow, yielding in less disease. 2. You rejuvenate new growth which increases flower production.

Pruning deciduous shrubs can be divided into 4 groups: Those that require minimal pruning (take out only dead, diseased, damaged, or crossed branches, can be done in early spring.); spring pruning (encourages vigorous, new growth which produces summer flowers - in other words, flowers appear on new wood); summer pruning after flower (after flowering, cut back shoots, and take out some of the old growth, down to the ground); suckering habit pruning (flowers appear on wood from previous year. Cut back flowered stems by 1/2, to strong growing new shoots and remove 1/2 of the flowered stems a couple of inches from the ground) Always remove dead, damaged or diseased wood first, no matter what type of pruning you are doing.

Examples: Minimal: Amelanchier, Aronia, Chimonanthus, Clethra, Cornus alternifolia, Daphne, Fothergilla, Hamamelis, Poncirus, Viburnum. Spring: Abelia, Buddleia, Datura, Fuchsia, Hibiscus, Hypericum, Perovskia, Spirea douglasii/japonica, Tamarix. Summer after flower: Buddleia alternifolia, Calycanthus, Chaenomeles, Corylus, Cotoneaster, Deutzia, Forsythia, Magnolia x soulangeana/stellata, Philadelphus, Rhododendron sp., Ribes, Spirea x arguta/prunifolia/thunbergii, Syringa, Weigela. Suckering: Kerria

How-to : Planting Shrubs

Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.

Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.

If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.

If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.

Problems

Fungi : Rusts

Most rusts are host specific and overwinter on leaves, stems and spent flower debris. Rust often appears as small, bright orange, yellow, or brown pustules on the underside of leaves. If touched, it will leave a colored spot of spores on the finger. Caused by fungi and spread by splashing water or rain, rust is worse when weather is moist.

Prevention and Control: Plant resistant varieties and provide maximum air circulation. Clean up all debris, especially around plants that have had a problem. Do not water from overhead and water only during the day so that plants will have enough time to dry before night. Apply a fungicide labeled for rust on your plant.

Fungi : Powdery Mildew

Powdery Mildew is usually found on plants that do not have enough air circulation or adequate light. Problems are worse where nights are cool and days are warm and humid. The powdery white or gray fungus is usually found on the upper surface of leaves or fruit. Leaves will often turn yellow or brown, curl up, and drop off. New foliage emerges crinkled and distorted. Fruit will be dwarfed and often drops early.

Prevention and Control: Plant resistant varieties and space plants properly so they receive adequate light and air circulation. Always water from below, keeping water off the foliage. This is paramount for roses. Go easy on the nitrogen fertilizer. Apply fungicides according to label directions before problem becomes severe and follow directions exactly, not missing any required treatments. Sanitation is a must - clean up and remove all leaves, flowers, or debris in the fall and destroy.

Weeds : Preventing Weeds and Grass

Weeds rob your plants of water, nutrients and light. They can harbor pests and diseases. Before planting, remove weeds either by hand or by spraying an herbicide according to label directions. Another alternative is to lay plastic over the area for a couple of months to kill grass and weeds.

You may apply a pre-emergent herbicide prior to planting, but be sure that it is labeled for the plants you are wishing to grow. Existing beds may be spot sprayed with a nonselective herbicide, but be careful to shield those plants you do not want to kill. Non-selective means that it will kill everything it comes in contact with.

Mulch plants with a 3 inch layer of pinestraw, pulverized bark, or compost. Mulch conserves moisture, keeps weeds down, and makes it easier to pull when necessary.

Porous landscape or open weave fabric works too, allowing air and water to be exchanged.

Miscellaneous

Glossary : Rock Garden

A rock garden is a garden that mimics an alpine area, having dwarf conifers, low-growing sub-shrubs, perennials and ground cover. Often, the soil itself tends to be gravelly or rocky.

Glossary : Sandy Loam

Sandy Loam refers to a soil that drains well, with excellent air space, and evenly crumbled texture when squeezed in the hand. A good workable garden soil that benefits from added fertilizer and proper watering. Dark gray to gray-brown in color.

Glossary : Loam

Loam is the ideal soil, having the perfect balance between particle size, air space, organic matter and water holding capacity. It forms a nice ball when squeezed in the palm of the hand, but crumbles easily when lightly tapped with a finger. Rich color ranges between gray brown to almost black.

Glossary : Clayey Loam

Clayey loam refers to a soil that retains moisture well, without having a drainage problem. Fertility is high and texture good. Easily forms a ball when squeezed in the hand, and then crumbles easily with a quick tap of the finger. Considered an ideal soil. Usually a rich brown color.

Glossary : Evergreen

Evergreen refers to plants that hold onto their leaves or needles for more than one growing season, shedding them over time. Some plants such as live oaks are evergreen, but commonly shed the majority of their older leaves around the end of January.

Glossary : pH

pH, means the potential of Hydrogen, is the measure of alkalinity or acidity. In horticulture, pH refers to the pH of soil. The scale measures from 0, most acid, to 14, most alkaline. Seven is neutral. Most plants prefer a range between 5.5 and about 6.7, an acid range, but there are plenty of other plants that like soil more alkaline, or above 7. A pH of 7 is where the plant can most easily absorb the most nutrients in the soil. Some plants prefer more or less of certain nutrients, and therefore do better at a certain pH.

Glossary : Heat Zone

The 12 zones of the AHS Heat Zone map indicate the average number of days each year that a given region experiences ""heat days"" or temperatures over 86 degrees F(30 degrees Celsius). That is the point at which plants begin suffering physiological damage from heat. The zones range from Zone 1 (less than one heat day) to Zone 12 (more than 210 heat days). The AHS Heat Zone, which deals with heat tolerance, should not be confused with the USDA Hardiness Zone system which deals with cold tolerance. For example: Seattle, Washington has a USDA Hardiness Zone of 8, the same as Charleston, South Carolina; however Seattle's Heat Zone is 2 where Charleston's Heat Zone is 11. What this says is that winter temperature in the two cities may be similar, but because Charleston has significantly warmer weather for a longer period of time, plant selection based on heat tolerance is a factor to consider.

Glossary : Plant Characteristics

Plant characteristics define the plant, enabling a search that finds specific types of plants such as bulbs, trees, shrubs, grass, perennials, etc.

Glossary : Small Shrub

A small shrub is less than 3 feet tall.

Glossary : Flower Characteristics

Flower characteristics can vary greatly and may help you decide on a ""look or feel"" for your garden. If you're looking for fragrance or large, showy flowers, click these boxes and possibilities that fit your cultural conditions will be shown. If you have no preference, leave boxes unchecked to return a greater number of possibilities.

Glossary : Foliage Characteristics

By searching foliage characteristics, you will have the opportunity to look for foliage with distinguishable features such as variegated leaves, aromatic foliage, or unusual texture, color or shape. This field will be most helpful to you if you are looking for accent plants. If you have no preference, leave this field blank to return a larger selection of plants.

Glossary : U. S. Natives

Native plants require lower maintenance and usually have less pest problems. They are key components in the xeriphytic landscape and backyard wildlife habitat. Select your region and the search will look for all plants in the database that are native to your area.

Glossary : Soil Types

A soil type is defined by granule size, drainage, and amount of organic material in the soil. The three main soil types are sand, loam and clay. Sand has the largest particle size, no organic matter, little to no fertility, and drains rapidly. Clay, at the opposite end of the spectrum, has the smallest particle size, can be rich in organic matter, fertility and moisture, but is often unworkable because particles are held together too tightly, resulting in poor drainage when wet, or is brick-like when dry. The optimum soil type is loam, which is the happy median between sand and clay: It is high in organic matter, nutrient-rich, and has the perfect water holding capacity.

You will often hear loam referred to as a sandy loam (having more sand, yet still plenty of organic matter) or a clay loam (heavier on the clay, yet workable with good drainage.) The addition of organic matter to either sand or clay will result in a loamy soil. Still not sure if your soil is a sand, clay, or loam? Try this simple test. Squeeze a handfull of slightly moist, not wet, soil in your hand. If it forms a tight ball and does not fall apart when gently tapped with a finger, your soil is more than likely clay. If soil does not form a ball or crumbles before it is tapped, it is sand to very sandy loam. If soil forms a ball, then crumbles readily when lightly tapped, it's a loam. Several quick, light taps could mean a clay loam.

Glossary : Ground Cover

Aground cover is any low growing plant that is planted in a mass to cover the ground. Shrubs, vines, perennials, and annuals can all be considered ground covers if they are grouped in this fashion. Ground covers can beautify an area, help reduce soil erosion, and the need to weed.

Glossary : Fertilize

Fertilize just before new growth begins with a complete fertilizer.

Glossary : Pruning

Now is the preferred time to prune this plant.

Plant Images