Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.

If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.

If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.

How-to : Preparing Containers

Containers are excellent when used as an ornamental feature, a planting option when there is little or no soil to plant in, or for plants that require a soil type not found in the garden or when soil drainage in the garden is inferior. If growing more than one plant in a container, make sure that all have similar cultural requirements. Choose a container that is deep and large enough to allow root development and growth as well as proportional balance between the fully developed plant and the container. Plant large containers in the place you intend them to stay. All containers should have drainage holes. A mesh screen, broken clay pot pieces(crock) or a paper coffee filter placed over the hole will keep soil from washing out. The potting soil you select should be an appropriate mix for the plants you have chosen. Quality soils (or soil-less medias) absorb moisture readily and evenly when wet. If water runs off soil upon initial wetting, this is an indicator that your soil may not be as good as you think.

Prior to filling a container with soil, wet potting soil in the bag or place in a tub or wheelbarrow so that it is evenly moist. Fill container about halfway full or to a level that will allow plants, when planted, to be just below the rim of the pot. Rootballs should be level with soil line when project is complete. Water well.

How-to : Potting Indoor Plants

Make sure that the plant you have chosen is suitable for the conditions you are able to provide it: that it will have enough light, space, and a temperature it will like. Remember that the area right next to a window will be colder than the rest of the room.

Indoor plants need to be transplanted into a larger container periodically, or they become pot/root-bound and their growth is retarded. Water the plant well before starting, so the soil will hold the root ball together when you remove it from the pot. If you have trouble getting the plant out of the pot, try running a blade around the edge of the pot, and gently whacking the sides to loosen the soil.

Always use fresh soil when transplanting your indoor plant. Fill around the plant gently with soil, being careful not to pack too tightly -- you want air to be able to get to the roots. After the plant is in the new pot, don't fertilize right away... this will encourage the roots to fill in their new home.

The size pot you choose is important too. Select one that is not more than about 1 inch greater in diameter. Remember, many plants prefer being somewhat pot bound. Always start with a clean pot!

How-to : Planting a Tree

Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.

If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.

If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.

Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.

Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.