Acer palmatum ( Ben Kawa Japanese Maple )

Characteristics

Cultivar:	Ben Kawa
Family:	Aceraceae
Size:	Height: 3 ft. to 12 ft. Width: 3 ft. to 11 ft.
Plant Category:	shrubs, trees,
Plant Characteristics:	low maintenance, spreading, weeping,
Foliage Characteristics:	deciduous,
Foliage Color:	yellow-green to gold,
Flower Characteristics:
Flower Color:
Tolerances:

Requirements

Bloomtime Range:	Early Spring to Mid Spring
USDA Hardiness Zone:	6 to 8
AHS Heat Zone:	3 to 3
Light Range:	Shade to Sun
pH Range:	4 to 7.5
Soil Range:	Some Sand to Some Clay
Water Range:	Normal to Moist

Plant Care

Fertilizing

How-tos : Fertilization for Established Plants

Established plants can benefit from fertilization. Take a visual inventory of your landscape. Trees need to be fertilized every few years. Shrubs and other plants in the landscape can be fertilized yearly. A soil test can determine existing nutrient levels in the soil. If one or more nutrients is low, a specific instead of an all-purpose fertilizer may be required. Fertilizers that are high in N, nitrogen, will promote green leafy growth. Excess nitrogen in the soil can cause excessive vegetative growth on plants at the expense of flower bud development. It is best to avoid fertilizing late in the growing season. Applications made at that time can force lush, vegetative growth that will not have a chance to harden off before the onset of cold weather.

How-tos : Fertilization for Annuals and Perennials

Annuals and perennials may be fertilized using: 1.water-soluble, quick release fertilizers; 2. temperature controlled slow-release fertilizers; or 3. organic fertilizers such as fish emulsion. Water soluble fertilizers are generally used every two weeks during the growing season or per label instructions. Controlled, slow-release fertilizers are worked into the soil ususally only once during the growing season or per label directions. For organic fertilizers such as fish emulsion, follow label directions as they may vary per product.

Light

Conditions : Partial Shade

Partial Shade is defined as filtered light found beneath trees with high limbs. Partial shade usually offers some protection from direct afternoon sun.

Conditions : Full to Partial Shade

Full shade means there is little or no light in the growing zone. Shade can be the result of a mature stand of trees or shadows cast by a house or building. Plants that require full shade are usually susceptible to sunburn. Full shade beneath trees may pose additional problems; not only is there no light, but competition for water, nutrients and root space.

Partial shade means that an area receives filtered light, often through tall branches of an open growing tree. Root competition is usually less. Partial shade can also be achieved by locating a plant beneath an arbor or lathe-like structure. Shadier sides of a building are normally the northern or northeastern sides. These sides also tend to be a little cooler. It is not uncommon for plants that can tolerate full sun or some sun in cooler climates to require some shade in warmer climates due to stress placed on the plant from reduced moisture and excessive heat.

Conditions : Partial Sun, Partial Shade

Part sun or part shade plants prefer light that is filtered. Sunlight, though not direct, is important to them. Often morning sun, because it is not as strong as afternoon sun, can be considered part sun or part shade. If you live in an area that does not get much intense sun, such as the Pacific Northwest, a full sun exposure may be fine. In other areas such as Florida, plant in a location where afternoon shade will be received.

Watering

Problems : Creating a Water Ring

A water ring, sometimes called a water well, is a mound of compacted soil that is built around the circumference of a planting hole once a plant has been installed. The water ring helps to direct water to the outer edges of a planting hole, encouraging new roots to grow outward, in search of moisture. The height of the mound of soil will vary from a couple of inches for 3 gallon shrubs, to almost a foot for balled and burlapped trees, especially those planted on a slope. Mulch over the ring will help to further conserve moisture and prevent deterioration of the ring itself. Once a plant is established, the water ring may be leveled, but you should continue to mulch beneath the plant.

Conditions : Moist and Well Drained

Moist and well drained means exactly what it sounds like. Soil is moist without being soggy because the texture of the soil allows excess moisture to drain away. Most plants like about 1 inch of water per week. Amending your soil with compost will help improve texture and water holding or draining capacity. A 3 inch layer of mulch will help to maintain soil moisture and studies have shown that mulched plants grow faster than non-mulched plants.

Planting

How-tos : Planting Shrubs

Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.

Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.

If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.

If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.

How-tos : Planting a Tree

Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.

If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.

If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.

Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.

Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.

Problems

Miscellaneous

Plant Images