Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.

If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.

If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.

How-to : Planting Perennials

Determine appropriate perennials for your garden by considering sun and shade through the day, exposure, water requirements, climate, soil makeup, seasonal color desired, and position of other garden plants and trees.

The best times to plant are spring and fall, when soil is workable and out of danger of frost. Fall plantings have the advantage that roots can develop and not have to compete with developing top growth as in the spring. Spring is more desirable for perennials that dislike wet conditions or for colder areas, allowing full establishment before first winter. Planting in summer or winter is not advisable for most plants, unless planting a more established sized plant.

To plant container-grown plants: Prepare planting holes with appropriate depth and space between. Water the plant thoroughly and let the excess water drain before carefully removing from the container. Carefully loosen the root ball and place the plant in the hole, working soil around the roots as you fill. If the plant is extremely root bound, separate roots with fingers. A few slits made with a pocket knife are okay, but should be kept to a minimum. Continue filling in soil and water thoroughly, protecting from direct sun until stable.

To plant bare-root plants: Plant as soon as possible after purchase. Prepare suitable planting holes, spread roots and work soil among roots as you fill in. Water well and protect from direct sun until stable.

To plant seedlings: A number of perennials produce self-sown seedlings that can be transplanted. You may also start your own seedling bed for transplanting. Prepare suitable planting holes, spacing appropriately for plant development. Gently lift the seedling and as much surrounding soil as possible with your garden trowel, and replant it immediately, firming soil with fingertips and water well. Shade from direct sun and water regularly until stable.

How-to : Staking Trees

Staking is done differently depending on the size and flexibility of the tree, and the windiness of the planting site. Generally only trees that are planted in windy, exposed locations need to be staked. For most trees, a low stake is preferred, to let the tree move naturally. For windy areas or flexible trees, use a high stake. For trees more than 12 feet tall, use two low stakes on opposite sides of the tree or several guy ropes. The ties used need to accommodate growth and not cause bark damage with friction. Buckle-and-spacer ties can be found at garden centers, they are expandable and have a protective spacer. Ties without spacers should be formed into a figure eight to create padding. Latest studies have shown that when staking a tree, provide enough leeway so that the tree can move back and forth in the wind. Stronger roots will develop this way. If the tree can not move back and forth, these important roots will not develop and the tree might fall over during a storm, once stakes are removed. When planting a tree, stake at the time of planting if staking is a necessity.

How-to : Planting a Tree

Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.

If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.

If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.

Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.

Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.