Cupressus macrocarpa is a medium large evergreen cypress tree, reaching 100 tall. This is an artistic beautiful tree, horizontally branching, and flat topped. The needles are a rich dark green, very attractive. A canker has unfortunately devasted many of these trees, and they have been removed. They are very salt tolerant, but not tolerant of high heat and humidity. Prefer hot, dry, well drained conditions. This species is one of the parents of x C.leylandii. Native to the Monterey area of California. Yellow needled cultivars are best used in cool climate areas.Important Info : A canker has unfortunately devasted many of these trees, and they have been removed. They are very salt tolerant, but not tolerant of high heat and humidity.
Google Plant Images: click here!
Size:Height: 0 ft. to 100 ft.
Width: 0 ft. to 40 ft.
Foliage Characteristics:fragrant, evergreen,
Tolerances:deer, drought, rabbits, seashore, wind,
Bloomtime Range: not applicable
USDA Hardiness Zone:7 to 9
AHS Heat Zone:Not defined for this plant
Light Range:Sun to Full Sun
pH Range:5.5 to 7.5
Soil Range:Some Sand to Clay Loam
Water Range:Dry to Moist
FertilizingHow-to : Fertilization for Young Plants
Young plants need extra phosphorus to encourage good root development. Look for a fertilizer that has phosphorus, P, in it(the second number on the bag.) Apply recommended amount for plant per label directions in the soil at time of planting or at least during the first growing season.
LightConditions : Full Sun
Full Sun is defined as exposure to more than 6 hours of continuous, direct sun per day.
WateringConditions : Regular Moisture for Outdoor Plants
Water when normal rainfall does not provide the preferred 1 inch of moisture most plants prefer. Average water is needed during the growing season, but take care not to overwater. The first two years after a plant is installed, regular watering is important. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.
PlantingHow-to : Planting a Tree
Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.
If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.
If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.
Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.
Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.
MiscellaneousConditions : Salt Tolerant
Anyone that lives close to the coast or in areas where soil salt content is high, can appreciate a plant that is salt tolerant. Salt damage is usually worse where the climate is arid: there is not enough rainfall to wash built up salts from the soil. It takes about 30 inches of rainfall a year to move salt through the soil. Plants that have salt damage usually have yellow leaves, brown tips or margins, and leaf drop. Soils may have a crusty white layer, too. Salt tolerant plants are often natives or introduced plants that have evolved in salty conditions.
Conditions : Wind Tolerant
Plants that are wind tolerant usually have flexible, strong branches that are not brittle. Wind tolerant plants often have thick or waxy leaves that control moisture loss from whipping winds. Native plants are often the best adapted to not only wind, but also soil and other climatic conditions.
Glossary : Specimen
A specimen can be a tree, shrub, ground cover, annual, or perennial that is unique in comparison to the surrounding plants. Uniqueness may be in color, form, texture, or size. By using only one specimen plant in a visual area, it can be showcased. Specimen plants are accents in the landscape, just as statues, water features, or arbors.
Glossary : U. S. Natives
Native plants require lower maintenance and usually have less pest problems. They are key components in the xeriphytic landscape and backyard wildlife habitat. Select your region and the search will look for all plants in the database that are native to your area.
Glossary : Drought Tolerant
Very few plants, except for those naturally found in desert situations, can tolerate arid soils, but there are plants that seem to be more drought tolerant than others. Plants that are drought tolerant still require moisture, so don't think that they can go for extended period without any water. Drought tolerant plants are often deep rooted, have waxy or thick leaves that conserve water, or leaf structures that close to minimize transpiration. All plants in droughty situations benefit from an occasional deep watering and a 2-3 inch thick layer of mulch. Drought tolerant plants are the backbone of xeriphytic landscaping.