This upright, deciduous shrub is an old-time favorite found in informal borders and hedges. Growing to a height of 10 feet tall and 6 feet wide, this shrub is loved primarily for its funnel-shaped flowers that resemble those of the tropical hibiscus, yet not as flashy. Leaves are diamond-shaped, dark green, slightly palmate and toothed. ‘William R. Smith’ bears large, to 4 inches wide, white blooms from late summer until mid-fall. Soil should be well-drained neutral to slightly alkaline and sun should be full, though partial shade is tolerated. This plant really requires no pruning, unless you need to remove a dead or damaged branch. Native from China to India.
Google Plant Images: click here!
CharacteristicsCultivar: William R. Smith
Size: Height: 10 ft. to 10 ft.
Width: 6 ft. to 6 ft.
Plant Category: shrubs,
Plant Characteristics: low maintenance,
Foliage Characteristics: deciduous,
Flower Characteristics: long lasting,
Flower Color: whites,
Tolerances: deer, drought, heat & humidity, pollution, rabbits, seashore,
Bloomtime Range: Mid Summer to Early Fall
USDA Hardiness Zone: 5 to 9
AHS Heat Zone: Not defined for this plant
Light Range: Part Shade to Full Sun
pH Range: 7 to 7.5
Soil Range: Some Sand to Some Clay
Water Range: Normal to Moist
FertilizingHow-to : Fertilization for Established Plants
Established plants can benefit from fertilization. Take a visual inventory of your landscape. Trees need to be fertilized every few years. Shrubs and other plants in the landscape can be fertilized yearly. A soil test can determine existing nutrient levels in the soil. If one or more nutrients is low, a specific instead of an all-purpose fertilizer may be required. Fertilizers that are high in N, nitrogen, will promote green leafy growth. Excess nitrogen in the soil can cause excessive vegetative growth on plants at the expense of flower bud development. It is best to avoid fertilizing late in the growing season. Applications made at that time can force lush, vegetative growth that will not have a chance to harden off before the onset of cold weather.
LightConditions : Full to Partial Shade
Full shade means there is little or no light in the growing zone. Shade can be the result of a mature stand of trees or shadows cast by a house or building. Plants that require full shade are usually susceptible to sunburn. Full shade beneath trees may pose additional problems; not only is there no light, but competition for water, nutrients and root space.
Partial shade means that an area receives filtered light, often through tall branches of an open growing tree. Root competition is usually less. Partial shade can also be achieved by locating a plant beneath an arbor or lathe-like structure. Shadier sides of a building are normally the northern or northeastern sides. These sides also tend to be a little cooler. It is not uncommon for plants that can tolerate full sun or some sun in cooler climates to require some shade in warmer climates due to stress placed on the plant from reduced moisture and excessive heat.
WateringProblems : Creating a Water Ring
A water ring, sometimes called a water well, is a mound of compacted soil that is built around the circumference of a planting hole once a plant has been installed. The water ring helps to direct water to the outer edges of a planting hole, encouraging new roots to grow outward, in search of moisture. The height of the mound of soil will vary from a couple of inches for 3 gallon shrubs, to almost a foot for balled and burlapped trees, especially those planted on a slope. Mulch over the ring will help to further conserve moisture and prevent deterioration of the ring itself. Once a plant is established, the water ring may be leveled, but you should continue to mulch beneath the plant.
Conditions : Normal Watering for Outdoor Plants
Normal watering means that soil should be kept evenly moist and watered regularly, as conditions require. Most plants like 1 inch of water a week during the growing season, but take care not to over water. The first two years after a plant is installed, regular watering is important for establishment. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.
PlantingHow-to : Planting Shrubs
Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.
Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.
If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.
If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.
ProblemsFungi : Leaf Spots
Leaf spots are caused by fungi or bacteria. Brown or black spots and patches may be either ragged or circular, with a water soaked or yellow-edged appearance. Insects, rain, dirty garden tools, or even people can help its spread.
Prevention and Control: Remove infected leaves when the plant is dry. Leaves that collect around the base of the plant should be raked up and disposed of. Avoid overhead irrigation if possible; water should be directed at soil level. For fungal leaf spots, use a recommended fungicide according to label directions.