Thicket-forming, erect deciduous shrub or small tree with spiny shoots. Grows to 20 feet tall and 15 feet wide. Bluish-green leaves are pinnate to 8 inch long, with 13-25 lanceolate, hairy leaflets. Pink, fragrant flowers, to 1 inch long are held in pendant racemes, to 4 inches long. Followed by brown, smooth seed pods, 4 inches long. With careful pruning while young, this very common and too often neglected tree, can be quite nice. Though a popular street tree, it really should not be used close to power lines where mature, hard wood has to be pruned. Native to New Mexico, Arizona.Important Info : Also known as Robinia luxurians.
Google Plant Images: click here!
Size: Height: 15 ft. to 20 ft.
Width: 13 ft. to 15 ft.
Plant Category: shrubs, trees,
Plant Characteristics: poisonous,
Foliage Characteristics: deciduous,
Flower Characteristics: long lasting, pendent, poisonous,
Flower Color: pinks,
Tolerances: drought, heat & humidity, slope,
Bloomtime Range: Late Spring to Early Summer
USDA Hardiness Zone: 5 to 9
AHS Heat Zone: Not defined for this plant
Light Range: Dappled to Full Sun
pH Range: 4.5 to 7.5
Soil Range: Some Sand to Some Clay
Water Range: Semi-Arid to Normal
FertilizingHow-to : Fertilization for Established Plants
Established plants can benefit from fertilization. Take a visual inventory of your landscape. Trees need to be fertilized every few years. Shrubs and other plants in the landscape can be fertilized yearly. A soil test can determine existing nutrient levels in the soil. If one or more nutrients is low, a specific instead of an all-purpose fertilizer may be required. Fertilizers that are high in N, nitrogen, will promote green leafy growth. Excess nitrogen in the soil can cause excessive vegetative growth on plants at the expense of flower bud development. It is best to avoid fertilizing late in the growing season. Applications made at that time can force lush, vegetative growth that will not have a chance to harden off before the onset of cold weather.
LightConditions : Dappled Light
Dappled Light refers to a dappled pattern of light created on the ground, as cast by light passing through high tree branches. This is the middle ground, not considered shady, but not sunny either. Dappled remains constant throughout the day.
Conditions : Sun
Sun is defined as the continuous, direct, exposure to 6 hours (or more) of sunlight per day.
Conditions : Light Conditions
Unless a site is completely exposed, light conditions will change during the day and even during the year. The northern and eastern sides of a house receive the least amount of light, with the northern exposure being the shadiest. The western and southern sides of a house receive the most light and are considered the hottest exposures due to intense afternoon sun.
You will notice that sun and shade patterns change during the day. The western side of a house may even be shady due to shadows cast by large trees or a structure from an adjacent property. If you have just bought a new home or just beginning to garden in your older home, take time to map sun and shade throughout the day. You will get a more accurate feel for your site's true light conditions.
Conditions : Light and Plant Selection
For best plant performance, it is desirable to match the correct plant with the available light conditions. Right plant, right place! Plants which do not receive sufficient light may become pale in color, have fewer leaves and a "leggy" stretched-out appearance. Also expect plants to grow slower and have fewer blooms when light is less than desirable. It is possible to provide supplemental lighting for indoor plants with lamps. Plants can also receive too much light. If a shade loving plant is exposed to direct sun, it may wilt and/or cause leaves to be sunburned or otherwise damaged.
Conditions : Full Sun
Full Sun is defined as exposure to more than 6 hours of continuous, direct sun per day.
WateringProblems : Creating a Water Ring
A water ring, sometimes called a water well, is a mound of compacted soil that is built around the circumference of a planting hole once a plant has been installed. The water ring helps to direct water to the outer edges of a planting hole, encouraging new roots to grow outward, in search of moisture. The height of the mound of soil will vary from a couple of inches for 3 gallon shrubs, to almost a foot for balled and burlapped trees, especially those planted on a slope. Mulch over the ring will help to further conserve moisture and prevent deterioration of the ring itself. Once a plant is established, the water ring may be leveled, but you should continue to mulch beneath the plant.
Conditions : Normal Watering for Houseplants
Houseplants that require normal watering should be watered so that soil is completely saturated and excess water runs out the bottom of the pot. Never water just a little bit; this allows mineral salts to build up in the soil. The key to normal watering is to allow the top inch or two of potting soil to dry out between waterings. Check frequently as certain times of the year may dictate that you water more frequently. Also, some plants that require normal watering during the growing season, may require less during the winter months when they are dormant.
Conditions : Moist and Well Drained
Moist and well drained means exactly what it sounds like. Soil is moist without being soggy because the texture of the soil allows excess moisture to drain away. Most plants like about 1 inch of water per week. Amending your soil with compost will help improve texture and water holding or draining capacity. A 3 inch layer of mulch will help to maintain soil moisture and studies have shown that mulched plants grow faster than non-mulched plants.
Conditions : Outdoor Watering
Plants are almost completely made up of water so it is important to supply them with adequate water to maintain good plant health. Not enough water and roots will wither and the plant will wilt and die. Too much water applied too frequently deprives roots of oxygen leading to plant diseases such as root and stem rots. The type of plant, plant age, light level, soil type and container size all will impact when a plant needs to be watered. Follow these tips to ensure successful watering:
* The key to watering is water deeply and less frequently. When watering, water well, i.e. provide enough water to thoroughly saturate the root ball. With in-ground plants, this means thoroughly soaking the soil until water has penetrated to a depth of 6 to 7 inches (1' being better). With container grown plants, apply enough water to allow water to flow through the drainage holes.
* Try to water plants early in the day or later in the afternoon to conserve water and cut down on plant stress. Do water early enough so that water has had a chance to dry from plant leaves prior to night fall. This is paramount if you have had fungus problems.
* Don't wait to water until plants wilt. Although some plants will recover from this, all plants will die if they wilt too much (when they reach the permanent wilting point).
* Consider water conservation methods such as drip irrigation, mulching, and xeriscaping. Drip systems which slowly drip moisture directly on the root system can be purchased at your local home and garden center. Mulches can significantly cool the root zone and conserve moisture.
* Consider adding water-saving gels to the root zone which will hold a reserve of water for the plant. These can make a world of difference especially under stressful conditions. Be certain to follow label directions for their use.
Conditions : Normal Watering for Outdoor Plants
Normal watering means that soil should be kept evenly moist and watered regularly, as conditions require. Most plants like 1 inch of water a week during the growing season, but take care not to over water. The first two years after a plant is installed, regular watering is important for establishment. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.
PlantingHow-to : Pruning Flowering Shrubs
It is necessary to prune your deciduous flowering shrub for two reasons: 1. By removing old, damaged or dead wood, you increase air flow, yielding in less disease. 2. You rejuvenate new growth which increases flower production.
Pruning deciduous shrubs can be divided into 4 groups: Those that require minimal pruning (take out only dead, diseased, damaged, or crossed branches, can be done in early spring.); spring pruning (encourages vigorous, new growth which produces summer flowers - in other words, flowers appear on new wood); summer pruning after flower (after flowering, cut back shoots, and take out some of the old growth, down to the ground); suckering habit pruning (flowers appear on wood from previous year. Cut back flowered stems by 1/2, to strong growing new shoots and remove 1/2 of the flowered stems a couple of inches from the ground) Always remove dead, damaged or diseased wood first, no matter what type of pruning you are doing.
Examples: Minimal: Amelanchier, Aronia, Chimonanthus, Clethra, Cornus alternifolia, Daphne, Fothergilla, Hamamelis, Poncirus, Viburnum. Spring: Abelia, Buddleia, Datura, Fuchsia, Hibiscus, Hypericum, Perovskia, Spirea douglasii/japonica, Tamarix. Summer after flower: Buddleia alternifolia, Calycanthus, Chaenomeles, Corylus, Cotoneaster, Deutzia, Forsythia, Magnolia x soulangeana/stellata, Philadelphus, Rhododendron sp., Ribes, Spirea x arguta/prunifolia/thunbergii, Syringa, Weigela. Suckering: Kerria
How-to : Pruning Trees After Planting
It is critical to prune trees correctly from the beginning to assure proper growth and development. Young trees can be transplanted in a number of forms: bare root, balled & burlap and in containers. The more stress the plant undergoes in the transplant process, the more pruning that is required to compensate.
Deciduous trees like maples (those that loose their leaves in the fall) can be dug up and sold with their bare roots exposed. Because most of the root system is lost in digging, sufficient top growth should be removed to compensate for this loss. This may be done at the nursery before you buy the plant or you may have to prune at the time of planting. Select and head back the best scaffold branches, i.e. those branches which will form the main lateral structure of the future mature tree. Remove all other extraneous side branches. If the tree seedling does not have branches, allow it to grow to the desired height of branching then pinch it back to stimulate the lower buds to form branches.
Ball and burlap trees are dug up with their root systems somewhat intact. This was mostly done for conifers and broadleaf evergreens, but has become common for deciduous trees as well. Since some root mass is lost in the digging stage, a light pruning is generally called for. Head back the plant to compensate for this loss and to promote branching.
Trees that are grown in containers generally do not loose roots in the transplanting phase. Therefore you do not generally have to prune them unless there is some root injury or limb damage in the planting process.
Once you have your trees planted, be patient. Do not remove shoots from the trunk early on as these allow the tree to grow more rapidly and also shade the tender young trunk from sun-scald. Wait a few years to begin training the tree to its ultimate form.
How-to : Planting Shrubs
Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.
Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.
If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.
If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.
How-to : Planting a Tree
Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.
If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.
If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.
Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.
Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.
ProblemsDiseases : Verticillium or Fusarium Wilt
Wilts may be contracted through infected seed, plant debris, or soil. This fungus begins and multiplies during the cool, moist season, becoming obvious when weather turns warm and dry. Plants wilt because the fungus damages their water conducting mechanisms. Overfertilization can worsen this problem. Able to overwinter in soil for many years, it is also carried and harbored in common weeds.
Prevention and Control: If possible, select resistant varieties. Keep nitrogen-heavy fertilizers to a minimum as well as over-irrigating as they encourage lush growth. Practice crop rotation and prune out or better yet remove infected plants.
Pest : Whiteflies
Whiteflies are small, winged insects that look like tiny moths, which attack many types of plants. The flying adult stage prefers the underside of leaves to feed and breed. Whiteflies can multiply quickly as a female can lay up to 500 eggs in a life span of 2 months. If a plant is infested with whiteflies, you will see a cloud of fleeing insects when the plant is disturbed. Whiteflies can weaken a plant, eventually leading to plant death if they are not checked. They can transmit many harmful plant viruses. They also produce a sweet substance called honeydew (coveted by ants) which can lead to an unattractive black surface fungal growth called sooty mold.
Possible controls: keep weeds down; use screening in windows to keep them out; remove infested plants away from non-infested plants; use a reflective mulch (aluminum foil) under plants (this repels whiteflies); trap with yellow sticky cards, apply labeled pesticides; encourage natural enemies such as parasitic wasps in the garden; and sometimes a good steady shower of water will wash them off the plant.
Fungi : Powdery Mildew
Powdery Mildew is usually found on plants that do not have enough air circulation or adequate light. Problems are worse where nights are cool and days are warm and humid. The powdery white or gray fungus is usually found on the upper surface of leaves or fruit. Leaves will often turn yellow or brown, curl up, and drop off. New foliage emerges crinkled and distorted. Fruit will be dwarfed and often drops early.
Prevention and Control: Plant resistant varieties and space plants properly so they receive adequate light and air circulation. Always water from below, keeping water off the foliage. This is paramount for roses. Go easy on the nitrogen fertilizer. Apply fungicides according to label directions before problem becomes severe and follow directions exactly, not missing any required treatments. Sanitation is a must - clean up and remove all leaves, flowers, or debris in the fall and destroy.
Pest : Caterpillars
Caterpillars are the immature form of moths and butterflies. They are voracious feeders attacking a wide variety of plants. They can be highly destructive and are characterized as leaf feeders, stem borers, leaf rollers, cutworms and tent-formers.
Prevention and Control: keep weeds down, scout individual plants and remove caterpillars, apply labeled insecticides such as soaps and oils, take advantage of natural enemies such as parasitic wasps in the garden and use Bacillus thuringiensis (biological warfare) for some caterpillar species.
Fungi : Leaf Spots
Leaf spots are caused by fungi or bacteria. Brown or black spots and patches may be either ragged or circular, with a water soaked or yellow-edged appearance. Insects, rain, dirty garden tools, or even people can help its spread.
Prevention and Control: Remove infected leaves when the plant is dry. Leaves that collect around the base of the plant should be raked up and disposed of. Avoid overhead irrigation if possible; water should be directed at soil level. For fungal leaf spots, use a recommended fungicide according to label directions.
Pest : Leaf Miners
Leaf Miner is actually a term that applies to various larvae (of moths, beetles, and flies) that tunnel between upper and lower leaf surfaces, leaving a distinctive, squiggly pattern. A female adult can lay several hundred eggs inside the leaf which hatch and give rise to miners. Leaf miners attack ornamentals and vegetables.
Prevention and Control: Keep weeds down and scout individual plants for tell-tale squiggles. Pick and destroy these leaves and take advantage of natural enemies such as parasitic wasps. Know the Growing Degree Days (GDD)* for your area to target insecticide sprays when most beneficial for controlling the specific leaf miner. Seek a professional recommendation and follow all label procedures to a tee. *GDD numbers should be available from your local Cooperative Extension office.
Pest : Scale Insects
Scales are insects, related to mealy bugs, that can be a problem on a wide variety of plants - indoor and outdoor. Young scales crawl until they find a good feeding site. The adult females then lose their legs and remain on a spot protected by its hard shell layer. They appear as bumps, often on the lower sides of leaves. They have piercing mouth parts that suck the sap out of plant tissue. Scales can weaken a plant leading to yellow foliage and leaf drop. They also produce a sweet substance called honeydew (coveted by ants) which can lead to an unattractive black surface fungal growth called sooty mold.
Prevention and Control: Once established they are hard to control. Isolate infested plants away from those that are not infested. Consult your local garden center professional or Cooperative Extension office in your county for a legal recommendation regarding their control. Encourage natural enemies such as parasitic wasps in the garden.
MiscellaneousConditions : Deer Tolerant
There are no plants that are 100% deer resistant, but many that are deer tolerant. There are plants that deer prefer over others. You will find that what deer will or will not eat varies in different parts of the country. A lot of it has to do with how hungry they are. Most deer will sample everything at least once, decide if they like it or not and return if favorable. A fence is the good deer barrier. You may go for a really tall one (7 to 8 feet), or try 2 parallel fences, (4 to 5 feet apart). Use a wire mesh fence rather than board, since deer are capable of wiggling through a 12 inch space.
Conditions : Slope Tolerant
Slope tolerant plants are those that have a fibrous root system and are often plants that prefer good soil drainage. These plants assist in erosion control by stabilizing/holding the soil on slopes intact.
Glossary : Deciduous
Deciduous refers to those plants that lose their leaves or needles at the end of the growing season.
Glossary : Poisonous
Poisonous: any plant or part of a plant which is toxic or irritating in any way.
Glossary : Shrub
Shrub: is a deciduous or evergreen woody perennial that has multiple branches that form near its base.
Glossary : Plant Characteristics
Plant characteristics define the plant, enabling a search that finds specific types of plants such as bulbs, trees, shrubs, grass, perennials, etc.
Glossary : Flower Characteristics
Flower characteristics can vary greatly and may help you decide on a ""look or feel"" for your garden. If you're looking for fragrance or large, showy flowers, click these boxes and possibilities that fit your cultural conditions will be shown. If you have no preference, leave boxes unchecked to return a greater number of possibilities.
Glossary : Foliage Characteristics
By searching foliage characteristics, you will have the opportunity to look for foliage with distinguishable features such as variegated leaves, aromatic foliage, or unusual texture, color or shape. This field will be most helpful to you if you are looking for accent plants. If you have no preference, leave this field blank to return a larger selection of plants.
Glossary : Drought Tolerant
Very few plants, except for those naturally found in desert situations, can tolerate arid soils, but there are plants that seem to be more drought tolerant than others. Plants that are drought tolerant still require moisture, so don't think that they can go for extended period without any water. Drought tolerant plants are often deep rooted, have waxy or thick leaves that conserve water, or leaf structures that close to minimize transpiration. All plants in droughty situations benefit from an occasional deep watering and a 2-3 inch thick layer of mulch. Drought tolerant plants are the backbone of xeriphytic landscaping.