This tropical plant is grown for its purple, tubular flowers. Leaves are oval and olive green and the trunk and bark of this tree is reddish brown. Relatively rare.
Google Plant Images: click here!
Characteristics
Cultivar: n/aFamily:
Size: Height: 0 ft. to 0 ft.
Width: 0 ft. to 0 ft.
Plant Category: trees,
Plant Characteristics:
Foliage Characteristics: medium leaves, coarse leaves,
Flower Characteristics: showy, single,
Flower Color: purples,
Tolerances: heat & humidity,
Requirements
Bloomtime Range: Early Summer to Late Summer
USDA Hardiness Zone: 10 to 11
AHS Heat Zone: Not defined for this plant
Light Range: Shade to Dappled
pH Range: 6.5 to 7.5
Soil Range: Sandy Loam to Some Clay
Water Range: Normal to Moist
Plant Care
Fertilizing
Light
Conditions : Partial Sun, Partial Shade Part sun or part shade plants prefer light that is filtered. Sunlight, though not direct, is important to them. Often morning sun, because it is not as strong as afternoon sun, can be considered part sun or part shade. If you live in an area that does not get much intense sun, such as the Pacific Northwest, a full sun exposure may be fine. In other areas such as Florida, plant in a location where afternoon shade will be received.
Watering
Conditions : Normal Watering for Houseplants Houseplants that require normal watering should be watered so that soil is completely saturated and excess water runs out the bottom of the pot. Never water just a little bit; this allows mineral salts to build up in the soil. The key to normal watering is to allow the top inch or two of potting soil to dry out between waterings. Check frequently as certain times of the year may dictate that you water more frequently. Also, some plants that require normal watering during the growing season, may require less during the winter months when they are dormant.
Conditions : Normal Watering for Outdoor Plants
Normal watering means that soil should be kept evenly moist and watered regularly, as conditions require. Most plants like 1 inch of water a week during the growing season, but take care not to over water. The first two years after a plant is installed, regular watering is important for establishment. The first year is critical. It is better to water once a week and water deeply, than to water frequently for a few minutes.
Planting
How-to : Planting Shrubs Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.
Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.
If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.
If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.
How-to : Preparing Containers
Containers are excellent when used as an ornamental feature, a planting option when there is little or no soil to plant in, or for plants that require a soil type not found in the garden or when soil drainage in the garden is inferior. If growing more than one plant in a container, make sure that all have similar cultural requirements. Choose a container that is deep and large enough to allow root development and growth as well as proportional balance between the fully developed plant and the container. Plant large containers in the place you intend them to stay. All containers should have drainage holes. A mesh screen, broken clay pot pieces(crock) or a paper coffee filter placed over the hole will keep soil from washing out. The potting soil you select should be an appropriate mix for the plants you have chosen. Quality soils (or soil-less medias) absorb moisture readily and evenly when wet. If water runs off soil upon initial wetting, this is an indicator that your soil may not be as good as you think.
Prior to filling a container with soil, wet potting soil in the bag or place in a tub or wheelbarrow so that it is evenly moist. Fill container about halfway full or to a level that will allow plants, when planted, to be just below the rim of the pot. Rootballs should be level with soil line when project is complete. Water well.
How-to : Potting Indoor Plants
Make sure that the plant you have chosen is suitable for the conditions you are able to provide it: that it will have enough light, space, and a temperature it will like. Remember that the area right next to a window will be colder than the rest of the room.
Indoor plants need to be transplanted into a larger container periodically, or they become pot/root-bound and their growth is retarded. Water the plant well before starting, so the soil will hold the root ball together when you remove it from the pot. If you have trouble getting the plant out of the pot, try running a blade around the edge of the pot, and gently whacking the sides to loosen the soil.
Always use fresh soil when transplanting your indoor plant. Fill around the plant gently with soil, being careful not to pack too tightly -- you want air to be able to get to the roots. After the plant is in the new pot, don't fertilize right away... this will encourage the roots to fill in their new home.
The size pot you choose is important too. Select one that is not more than about 1 inch greater in diameter. Remember, many plants prefer being somewhat pot bound. Always start with a clean pot!
How-to : Planting a Tree
Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.
If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.
If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.
Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.
Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.
Problems