There are 15 species trees and shrubs that fall into this genus. The are all evergreen and native to East Asia. Resembling Rhododendron foliage, the flowers are not showy. Grow in moist, rich soil in sun or shade.
Google Plant Images: click here!
Size:Height: 20 ft. to 20 ft.
Width: 19 ft. to 20 ft.
Foliage Characteristics:medium leaves, evergreen,
Tolerances:heat & humidity,
Bloomtime Range: Late Spring to Late Spring
USDA Hardiness Zone:7 to 10
AHS Heat Zone:Not defined for this plant
Light Range:Dappled to Full Sun
pH Range:4.5 to 6.5
Soil Range:Sandy Loam to Some Clay
Water Range:Normal to Normal
FertilizingHow-to : Fertilization for Young Plants
Young plants need extra phosphorus to encourage good root development. Look for a fertilizer that has phosphorus, P, in it(the second number on the bag.) Apply recommended amount for plant per label directions in the soil at time of planting or at least during the first growing season.
LightConditions : Partial Shade
Partial Shade is defined as filtered light found beneath trees with high limbs. Partial shade usually offers some protection from direct afternoon sun.
Conditions : Full Sun
Full Sun is defined as exposure to more than 6 hours of continuous, direct sun per day.
WateringConditions : Moist and Well Drained
Moist and well drained means exactly what it sounds like. Soil is moist without being soggy because the texture of the soil allows excess moisture to drain away. Most plants like about 1 inch of water per week. Amending your soil with compost will help improve texture and water holding or draining capacity. A 3 inch layer of mulch will help to maintain soil moisture and studies have shown that mulched plants grow faster than non-mulched plants.
PlantingHow-to : Planting Shrubs
Dig a hole twice the size of the root ball and deep enough to plant at the same level the shrub was in the container. If soil is poor, dig hole even wider and fill with a mixture half original soil and half compost or soil amendment.
Carefully remove shrub from container and gently separate roots. Position in center of hole, best side facing forward. Fill in with original soil or an amended mixture if needed as described above. For larger shrubs, build a water well. Finish by mulching and watering well.
If the plant is balled-and-burlapped, remove fasteners and fold back the top of natural burlap, tucking it down into hole, after you've positioned shrub. Make sure that all burlap is buried so that it won't wick water away from rootball during hot, dry periods. If synthetic burlap, remove if possible. If not possible, cut away or make slits to allow for roots to develop into the new soil. For larger shrubs, build a water well. Finish by mulching and watering well.
If shrub is bare-root, look for a discoloration somewhere near the base; this mark is likely where the soil line was. If soil is too sandy or too clayey, add organic matter. This will help with both drainage and water holding capacity. Fill soil, firming just enough to support shrub. Finish by mulching and watering well.
How-to : Planting a Tree
Dig out an area for the tree that is about 3 or 4 times the diameter of the container or rootball and the same depth as the container or rootball. Use a pitchfork or shovel to scarify the sides of the hole.
If container-grown, lay the tree on its side and remove the container. Loosen the roots around the edges without breaking up the root ball too much. Position tree in center of hole so that the best side faces forward. You are ready to begin filling in with soil.
If planting a balled and burlaped tree, position it in hole so that the best side faces forward. Untie or remove nails from burlap at top of ball and pull burlap back, so it does not stick out of hole when soil is replaced. Synthetic burlap should be removed as it will not decompose like natural burlap. Larger trees often come in wire baskets. Plant as you would a b&b plant, but cut as much of the wire away as possible without actually removing the basket. Chances are, you would do more damage to the rootball by removing the basket. Simply cut away wires to leave several large openings for roots.
Fill both holes with soil the same way. Never amend with less than half original soil. Recent studies show that if your soil is loose enough, you are better off adding little or no soil amendments.
Create a water ring around the outer edge of the hole. Not only will this conseve water, but will direct moisture to perimeter roots, encouraging outer growth. Once tree is established, water ring may be leveled. Studies show that mulched trees grow faster than those unmulched, so add a 3"" layer of pinestraw, compost, or pulverized bark over backfilled area. Remove any damaged limbs.